

Training	Online Store	Rentals	Sales & Service	Contact SKC

Headlines:	Sample Bag Stability Data		Green Building Testing	Nanoparticle Measurement	New! SKC Webinars/Podcast

Deal of the Month. Special pricing Click Here

Leland Legacy Sample Pump

5 to 15 L/min
High Flows and Long Run Times for Low Levels
24-Hour High Flow

Leland Legacy High Flow Air Sample Pump Cat. No. 100-3000

Leland Legacy Downloads

High flows from 5 to 15 L/min
Achieve flow rates that you couldn't reach before when using a personal sample pump. The Leland Legacy® provides the high flows and long run times of a vacuum-style pump in a compact, portable, and battery-operated sampler.

Long runs for 24 hours on one battery charge
Rechargeable lithium-ion (Li-Ion) battery pack provides 24-hour run times with impactors and other sampling devices with low back pressures*. Leland Legacy is ideal for 24-hour indoor air studies and unattended ambient air sampling.

*	Leland Legacy is not recommended for high back pressure applications such as asbestos clearance sampling.

Typical Run Time^†24+ hours:

Sioutas Impactor at 9 L/min (approximately 13 inches water back pressure)
Personal Environmental Monitor (PEM) with 37-mm, 2.0-µm PTFE filter 225-1709^‡at 10 L/min
Low-volume PUF Tube at 5 L/min
IMPACT Sampler (PM2.5 or PM10) at 10 L/min
For extended run times, the pump may be operated while attached to the approved charger.

^†	Results obtained using a new pump and new fully charged battery. Pump performance may vary.
^‡	Back pressure on PTFE filters can vary within the same lot. Maximum operating temperature is 464 F (240 C) based on support ring.

Low Levels
Longer runs at higher flows provide more sample for the enhanced sensitivity required for measuring low concentrations, particularly in indoor air environments.

Low Noise
With the noise-reducing case accessory, the Leland Legacy can operate at 10 L/min and 12 inches water back pressure with a noise level of only 52 dBA.**

** Measured 3 feet (1 meter) from pump operating at 10 L/min without media

Advanced flow control
The patented (U.S. Patent No. 5,892,160) internal flow sensor measures flow directly and acts as a secondary standard to constantly maintain the set flow. Set flow is achieved immediately at start-up and flow calibration is automatically maintained by built-in sensors that compensate for differences in temperature and atmospheric pressure during sampling.

Flexible programming

Manual three-button operation
No tools needed. Simply use the Leland Legacy built-in keypad to set, calibrate, and sample! Real-time sampling parameters are available at the touch of a button.
PC programmability
The ultimate in pump scheduling and record keeping. Use Leland Legacy with your PC and DataTrac for Leland Legacy Software to create complete running sequences, download sampling and calibration data, and generate sampling reports for ISO 9000, quality programs, and occupational health and safety management systems. DataTrac Software for Leland Legacy is included in the 5-pack kits and sold separately.

CalChek Direct Communication to a Primary Flow Standard

Leland Legacy in calibration train with DEFENDER calibrator

Accurate automatic calibration
The patented (U.S. Patent No's. 6,227,031 and 6,363,769) built-in CalChek feature provides hands-free calibration between a Defender primary standard calibrator and an SKC Leland Legacy pump for fast and easy calibration of the pumps internal flow sensor. The Defender calibrator is sold separately or in convenient Leland Legacy CalChek kits.

Leland Legacy Sampler Applications

Use in non-explosive locations only.

24-hour exposure monitoring
Indoor air studies
Particulate sampling:
- Pesticides — EPA TO-10A and ASTM 4861
- Bioaerosols (spore traps/cassettes)
- Cotton dust
- Radon decay products (ASTM D6327-98)
- Isokinetic sampling
Environmental sampling
Sampling with cascade impactors
Spore trap sampling (VersaTrap)
PM2.5 with PEM at 10 L/min (EPA IP-10A)

The Leland Legacy Advantage

Collects more sample
High flows and long run times greatly increase the amount of particulate matter collected when sampling low levels. This enhances the usefulness of the data for environmental health and epidemiology studies.

Designed for indoor environments
Noise, size, and weight are minimized relative to the high flow range.

Downloadable history
Critical sampling parameters are retained in memory during the sampling period and can be downloaded for record keeping.

Leland Legacy and Sioutas Impactor*

Suitable for use with the Leland Legacy Pump at 9 L/min, the Sioutas Impactor separates airborne particles precisely into five size ranges from ultrafine to PM2.5. When used with PTFE filters, the Sioutas Impactor is highly efficient at collecting particles without using impaction grease or coated substrate and at retaining unstable compounds for size-fractionated chemical analysis. The performance of the Leland Legacy pump with the Sioutas Impactor has been verified through EPA-ETV. Click here for more information on the Sioutas Impactor.

Click here for the SKC Update to EPA IP-10A (PDF)

* Developed by Dr. Constantinos Sioutas of the University of Southern California in partnership with NUATRC.

ETV Logo Leland Legacy and Sioutas Impactor Receive ETV Verification
U.S. EPA Environmental Technology Verification (EPA-ETV) is a program that furthers environmental protection by accelerating acceptance and use of improved, cost-effective technologies through performance verification. EPA-ETV tested the performance of the SKC Leland Legacy Sample Pump with the Sioutas Impactor. For a verification report, visit the AMS Center at http://www.epa.gov/etv/vt-ams.html.

The SKC Leland Legacy and NUATRC
The Leland Legacy was developed in partnership with the Mickey Leland National Urban Air Toxics Research Center (NUATRC) to further advance personal exposure measurement.

Established by Congress in the Clean Air Act Amendments of 1990 (CAAA), the non-profit Leland Center is responsible for investigating public health risks posed by air toxics to urban populations. The Leland Center is a private/public research partnership that brings together corporate, academic, and government scientists to develop a sound peer-reviewed air toxics research program. This program is jointly supported by the private sector and the U.S. EPA.

Performance Profile
Leland Legacy Sample Pump

Flow Range

5 to 15 L/min

Flow Control System

Closed loop with patented internal flow sensor
U.S. Patent No. 5,892,160

Compensation Range

15 L/min at 5 inches water back pressure
10 L/min at 12 inches water back pressure
5 L/min at 20 inches water back pressure

Accuracy

Flow rate: ± 5% of set-point after calibration to desired flow

Accuracy

Timing: 1 min/mo at 25 C

Accuracy

Atmospheric Pressure: ± 0.3 in Hg

Flow Fault

If the pump is unable to compensate for > 15 seconds due to excessive back pressure, a flow fault icon displays and flashes, the pump enters Hold mode, and the pump retains historical data. Auto restart is attempted every 20 seconds up to 10 times. Adjustable with DataTrac for Leland Legacy software

Tubing

Requires 3/8-inch ID tubing

Display

LCD, displays pump serial number, pump software revision level, flow rate, volume, temperature, atmospheric pressure, time of day, run time, and pump status, i.e., hold and run as well as Setup information

Volume Display

Continually updated, based on corrected flow rate multiplied by sampling time

Time Display

Time of day in hours and minutes (12 or 24-hour clock) with AM and PM indicators

Timer Display Range

1 to 99999 minutes (69 days). If the run time exceeds 69 days, the timer display rolls over.

Operating Temperature Range

32 to 113 F (0 to 45 C)
Protect sample pump from weather when in use outdoors.

Typical Run Time^†

24+ hours:

Sioutas Impactor at 9 L/min (approximately 13 inches water back pressure)
Personal Environmental Monitor (PEM) with 37-mm, 2.0-µm PTFE filter 225-1709^‡at 10 L/min
Low-volume PUF Tube at 5 L/min
DPS Sampler (PM2.5 or PM10) at 10 L/min
For extended run times, the pump may be operated while attached to the approved charger.

^†	Results obtained using a new pump and new fully charged battery. Pump and battery performance may vary.
^‡	Back pressure on PTFE filters can vary within the same lot. Maximum operating temperature is 464 F (240 C) based on support ring.

Noise Level

62.5 dBA — pump without case
52 dBA — pump housed in noise-reducing case (optional accessory Cat. No. 224-89) measured 3 ft (1 m) from pump operating at 10 L/min without media

User-adjustable Values

Sample run time, calibration, clock display, flow rate, time of day, delayed start, and temperature and atmospheric pressure display

Recorded Values

Start date and time, stop date and time, total sample time, flow rate, sample volume, temperature, atmospheric pressure, and pump mode transitions

Adjustable Logging Interval

Records pump history from 3 seconds (15.4 min of data) up to 8 hours (over 102 days of data) depending on setting. Option available when using DataTrac Software

Power Supply

Battery: removable, rechargeable lithium-ion (Li-Ion) battery pack 7.4 V x 12-Ah capacity, 88.8 Wh. (See Li-Ion Battery Shipment below.)
Charger/AC adapter: input voltage 100-240 V AC

Battery Recharge Time (with SKC-approved charger)

15 hrs

Temperature: Charging

32 to 113 F (0 to 45 C)

Temperature: Storage

-4 to 95 F (-20 to 35 C)

Size

8 x 3.9 x 2.6 in (20 x 10 x 7 cm)

Weight

36 oz (1 kg)

Case

Thermoplastic with soft rubber overmolding

RFI/EMI Shielding

CE marked

Ordering Information
Leland Legacy requires 3/8-inch ID tubing

Pump Kits and Accessories* Use in non-explosive locations only; not UL Listed for intrinsic safety. Leland Legacy Pumps contain Li-Ion batteries and may be subject to special shipping regulations.		Cat. No.
Leland Legacy Pump*with Li-Ion battery pack and screwdriver set Use in non-explosive environments only; not UL Listed for intrinsic safety; CE marked Requires charger; see kits or chargers below		100-3002
Single Pump Kitincludes Leland Legacy pump, Li-Ion battery pack, and single charger, in a Pelican carry case, CE marked Use in non-explosive locations only; not UL Listed for intrinsic safety*	100-240 V	100-3002K
Single Pump CalChek Kit* includes Leland Legacy pump, Li-Ion battery pack, single charger/adapter unit, Defender calibrator (Revision Level C, CalChek ready) with charger and CalChek communication cable, and Pelican carry case. CE marked Use in non-explosive locations only; not UL Listed for intrinsic safety	100-240 V	100-3002DFK
Single Pump Starter Kit includes pump with battery, charger, Tygon tubing (3 feet, ¼-inch ID), and collar clip with cable tie	100-240 V	100-3002-S
5-pack Pump Kit* includes 5 Leland Legacy pumps, Take Charge 5 Multi-charger, and DataTrac Software, in a Pelican case. CE marked Use in non-explosive locations only; not UL Listed for intrinsic safety	100-240 V	100-3002K5
**5-pack CalChek Kit*** includes items in 5-pack Leland Legacy pump kit, CalChek Kits, Li-Ion battery packs, DataTrac Software, and Defender calibrator (Revision Level C, CalChek ready) with charger, and CalChek communication cable, in a Pelican case. CE marked Use in non-explosive locations only; not UL Listed for intrinsic safety	100-240 V	100-3002DFK5
Pump Certificate
Certificate of Compliance, optional, must be ordered when ordering pump		P1501
Software
DataTrac Software for Leland Legacy includes software CD, DataTrac adapter, and DataTrac cable Requires Windows 98 or higher and available serial port or appropriate adapter compatible with PC and system Download DataTrac Software for Leland Legacy		877-92
Calibrators and Accessories
Defender 510 Model, 300 to 30,000 ml/min includes lead-acid battery, multi-plug charger (100-240 V), Optimizer Software, 39-inch (1-meter) serial cable, and leak test caps Software requires Windows® 2000, XP (sp 2 or 3), or Vista (32-bit version) and RS-232 port or USB to RS-232 adapter.		717-510H
Defender 520 Model, 300 to 30,000 ml/min includes lead-acid battery, multi-plug charger (100-240 V), Optimizer Software, and 39-inch (1-meter) serial cable, and leak test caps Software requires Windows® 2000, XP (sp 2 or 3), or Vista (32-bit version) and RS-232 port or USB to RS-232 adapter.		717-520H
Defender 530 Model, 300 to 30,000 ml/min includes lead-acid battery, multi-plug charger (100-240 V), Optimizer Software, 39-inch (1-meter) serial cable, and leak test caps Software requires Windows 2000, XP (sp 2 or 3), or Vista (32-bit version), and an RS-232 port or USB to RS-232 adapter.		717-530H
CalChek Communication Cable, provides direct communication between a CalChek-compatible AirChek 2000 or Leland Legacy pump and a CalChek-capable Defender primary standard calibrator; included in CalChek kits above *Note:* For use only with Defender calibrators with Revision Level C or higher		210-502
Defender Universal Charger, 100-240 V, with U.S., Euro, and Australia plugs		717-509
Defender Universal Charger, 100-240 V, with U.S. plug		717-507
Chargers and Accessories
Single Charger, for Li-Ion battery powered pumps, includes charging unit and wall cube (100-240 V worldwide power input with interchangeable plugs included)		223-241
Take Charge 5 Multi-charger, 5-station, for Li-Ion battery powered pumps (100-240 V) Use in non-explosive locations only; not UL Listed for intrinsic safety		223-441
Single Wall Cube/Power Supply, 100-240 V, with multiple plugs, included as part of Single Charger Cat. No. 223-241		223-245
Li-Ion Charging Unit, 100-240 V, included as part of Single Charger Cat. No.223-241 Note: Must be used in conjunction with the 223-245 Wall Cube Charger/Power Supply		P22300
Replacement Li-Ion Battery Charging Unit Cable, for charger 223-241		P75632
Battery Charging Adapter, for charging batteries outside the pump		223-248
Pump Carry Cases and Pouches
Noise-reducing Nylon Pump Pouch, black, with lining to reduce pump noise from 62.5 to 52 dB, includes waist belt and shoulder strap Measured 3 feet (1 meter) from pump operating at 10 L/min without media		224-89
Single, Pelican with foam		224-912
5-pack, Pelican on wheels for easy transport		224-905
Replacement Parts and Tools
Replacement Leland Legacy Battery Pack, Li-Ion		P75692
Replacement Filter/O-ring Set includes 5 filters and 1 O-ring		P40021B
Replacement Inlet Filters, pk/50		P40021A
Replacement PC Board, for Leland Legacy Sample Pump, main		P7954802
Replacement LCD		P72383
Replacement Inlet, for Leland Legacy Pump		P20198
Replacement Belt Clip, for Leland Legacy Pump		P51823
Leland Legacy Case includes front and back cases; does not include serial number label		P20187
Leland Legacy Control Board		P79549
Leland Legacy Motor		P78609
Leland Legacy Inlet Side Pulsation Dampener		P20148
Replacement Yoke/Crank Arm Insert Assembly		P21296
SKC Universal Screwdriver Kit, for use with sample pumps, includes 3 interchangeable screwdriver heads		224-11

Protect sample pump from weather when in use outdoors.

Li-Ion Battery Shipment
Rechargeable lithium-ion batteries for use with SKC sample pumps have been tested in accordance with the UN Manual and are proven to meet requirements of each test in the UN Manual of Test Criteria, Part III, subsection 38.3. They have a watt-hour (Wh) rating below 100.

Per 2010 IATA regulations, packaging must meet the specifications of and contain labeling and documentation required by IATA Packing Instructions 965, 966, and 967. See IATA Guidance
Document: Transport of Lithium Metal and Lithium Ion Batteries, Revised for the 2010 Regulations (PDF)

Leland Legacy Product Data Bulletin (PDF)

Leland Legacy Operating Instructions (PDF)

Leland Legacy Quick Guide (PDF)

CalChek with the Defender Operating Instructions (PDF)

Chinese Language Leland Legacy Operating Instructions (PDF)