SKC Inc. The World Leader in Sampling Technologies
English
Espanol
Deutsch
Francais
Portugues
systransoft.com
  Headlines:
          Anasorb CMS Status
 
Deal of the Month.  Special pricing Click Here

Low Flow Pumps
Pocket Pump 210 Series

Smallest Programmable Low Flow Sampler

210-1000 Low Flow Pumps The Pocket Pump ® 210 Series

A model that meets ATEx directive 94/9/EC is available

Ordering Information

Pocket Pump Spec. Sheet (PDF)

Pocket Pump Operating Instructions (PDF)

Pocket Pump Quick Guide (PDF)

Battery Pack for Pocket Pump Operating Instructions (PDF)

Technical Note: SKC Sample Pump Battery Pack Characteristics and Maintenance (PDF)

MSDS for Nickel Cadmium Battery GPI International (PDF)

MSDS for Nickel Cadmium Battery SANYO Energy (PDF)

MSDS for Nickel-metal Hydride Battery (PDF)

UL Certificate of Intrinsic Safety (PDF)

EMC Test Certificate (PDF)

DataTrac for the Pocket Pump

Instrucciones de Funcionamento (PDF)

Téléchargement Guide de I'utilisateur (PDF)

Chinese Language Pocket Pump Operating Instructions (PDF)

Pocket Pump FAQs


Advanced Technology in the Smallest Programmable Low Flow Pump

Constant flows from 20 to 225 ml/min
Accommodates most flow rates for sorbent tubes210-1000 Low Flow Pumps The Pocket Pump ® 210 Series  IN hand

Compact and lightweight
Only 4.5 x 2.2 x 1.4 inches (11.4 x 5.6 x 3.6 cm) and 5 ounces (142 grams)
Easily fits a shirt pocket or clips on a belt

Ultra-quiet operation
For greater worker acceptance

Multiple-tube sampling
With a multiple low-flow holder and CPC, sample with up to 4 tubes simultaneously, each at a different flow rate if desired. Save time and use fewer pumps.

PC-compatible with DataTrac Software

With optional DataTrac Software, program delayed, intermittent, and repeated sampling
Download data to PC for documentation of sampling history, record keeping, and data analysis

Electronic flow control; no tools required
Simple 3-button keypad does it all

Continuous sample volume calculations
Sampling parameters are continuously updated

Automatic features maintain sample integrity
Low battery and restricted flow shut off
Pump stores run time data in memory
Auto-restart after flow fault

RFI/EMI-shielded and CE marked
Flow unaffected by outside interferences
Accurate air volumes and data validity ensured

Large, easy-to-read LCD
Easily view sampling parameters and battery and fault status, all at the touch of a button

Pump-controlled charging
Never overcharges
Built-in system automatically senses maximum charge and switches to trickle charge to prolong battery life and prevent damage

Continuous run with AC adapter enables extended sampling
Useful for environmental monitoring or 24-hour sampling without harm to the battery pack

Security code system protects data

Requires code before changing operating parameters
Minimizes accidental changes or tampering and maintains sample validity

Impact-resistant case

Rugged case withstands rough handling in the industrial workplace

Intrinsically safe

UL and cUL Listed
Model available that meets ATEX Directive 94/9/EC (NiCad battery model only)
Safe in hazardous locations
Versatile for all industries

Ordering Information


Pocket Pump showing labeled parts 210-1000 Low Flow Pumps The Pocket Pump ® 210 Series Pocket Pump showing labeled parts 210-1000 Low Flow Pumps The Pocket Pump ® 210 Series

The 3-button Keypad Does It All
Use the three buttons under the sliding cover to operate the Pocket Pump at flows from 20 to 225 ml/min. Set the flow rate in constant flow mode for single sorbent tube applications, or set the back pressure in constant pressure mode for multiple-tube applications. The Pocket Pump accommodates flow ranges for most sorbent tube and long-duration detector tube methods. Users may also select the temperature and pressure scale. Security code protected operating mode and parameters minimizes tampering and maintains sample validity. The Pocket Pump may be placed in HOLD mode at any time without loss of data.

The Pocket Pump operates in either constant flow (single-tube sampling) or constant pressure (multiple-tube sampling) mode with flows from 20 to 225 ml/min. Operation is programmed using the 3-button keypad or a PC.

A built-in security code system prevents workers from changing operating state or parameters, ensuring sample validity. Multiple keys must be pressed to place the pump in HOLD; accidentally pressing one button will not alter pump operation.

Direct Readout of Data
The large easy-to-read LCD shows direct readouts of sample data that is continuously updated and may be displayed during sampling at the touch of a button. Simply press a key to scroll through the sample data that includes flow rate, air volume, temperature of the incoming air, and sample time. The LCD constantly displays a battery status icon, and a flashing flow fault icon appears when flow is restricted or blocked.

Pump-controlled Charging
Never worry about overcharging again. Since advanced electronics are built into the pump and not the charger, the smart charging battery system knows how much charging the pump needs; it never overcharges. The batteries may be charged with the battery charger while the pump is running. The Pocket Pump may operate indefinitely with the AC charger/adapter without harm to the battery pack.

The battery charge status icon is constantly displayed. When the pump loses all charge, it enters SLEEP mode while preserving the historical data in memory. When fully charged, the NiMH battery provides 12 hours of continuous use at 200 ml/min with back pressure up to 10 inches of water. Run times vary with media used.

PC Programmable with DataTrac Software
Use DataTrac Software (optional accessory) and your personal computer to make the Pocket Pump PC programmable. DataTrac simplifies chain-of-custody reporting by allowing users to program up to 14 complete running sequences including delayed start, timed stop, and intermittent sampling, all at different flow rates. Pump settings can be changed with the click of a mouse button. DataTrac’s Real-time Monitor window displays a real-time readout of the Pocket Pump’s operations including time and sample volume. Lengthy calculations are unnecessary; DataTrac does it all for you. The advanced information retrieval system is specifically designed to store data and provide chain-of-custody information. DataTrac also stores historical data in pump memory that can be retrieved up to 24 hours after shutdown.

  • Program the flow rate, start and stop date, and sample duration.
  • Schedule multiple start and stop times.
  • Create a sample setup sheet for worker, sample, and analysis information.
  • Download historical records of flow rate, sample time, air volume, temperature, and more.
  • Print or save a complete report of sample and pump history information.

Click here to go to the DataTrac Software Page

 


Twin Port Pocket Pump Cat.No. 210-1002APocket Pump for Bag Sampling

SKC offers Pocket Pumps with twin ports — an inlet port and an exhaust port — for bag sampling applications. The flow range for the Twin Port Pocket Pump is 20 to 225 ml/min.
This pump is not UL Listed for intrinsic safety.

 

 

 


Performance Profile

Flow Range in Constant Flow Mode
20 to 225 ml/min
Accuracy Variance Between LCD Reading and Actual Flow Rate (after calibration)
20 to 225 ml/min ± 5%
Constant Flow Compensation Range (inlet only)
20 to 225 ml/min up to 20 inches water back pressure
Flow Control Accuracy
± 5% of set-point in constant flow after calibration
Pressure Range in Constant Pressure (Multiple-tube Sampling) Mode (inlet only)
1 to 10 inches of water (1.87 to 18.7 mm Hg) at a maximum flow rate of 200 ml/min for 8 hrs (12 hrs if using NiMH battery)

10 to 20 inches water (18.7 to 37.4 mm Hg) at maximum flow rate of 100 ml/min for 8 hrs (12 hrs if using NiMH battery)
Constant Pressure (Multiple-tube Sampling) Mode Accuracy
Pressure reading ± 0.5 in of water (0.25 mm Hg)
Operating Temperature
32 to 113 F (0 to 45 C)
Storage Temperature
-4 to 113 F (-20 to 45 C)
Charging Temperature
40 to 100 F (5 to 38 C)
Operating Humidity 0 to 95% non-condensing
Run Time

Varies with flow rate and sampling media in line

At 200 ml/min and 10 inches water back pressure, nominal run time is approximately 8 hrs.

At 200 ml/min and 20 inches water back pressure, nominal run time is approximately 6 hrs.

Connected to a charger, run time is extended.

Nickel-metal hydride (NiMH) batteries increase run times up to 12 hrs in most sampling situations.

Timer Display Range
1 to 9999 minutes
Timing Accuracy
± 1%
Flow Fault
If the pump is unable to compensate for longer than 15 seconds due to excessive back pressure, the pump enters FLOW FAULT mode. The pump goes into HOLD, the fault icon appears on the display, and the accumulated run time display is frozen and retained. After 5 minutes in flow fault, auto-restart is attempted every 5 minutes until flow is corrected.
Battery Pack
Rechargeable NiCad battery pack, 2.4 V x 0.6 Ah or
Rechargeable NiMH battery pack, 2.4 V x 1.0 Ah
Charge Time
(varies with battery capacity and level of discharge)

< 6 hrs with Pocket Pump charger (battery attached to pump)
Approximately 16 hrs with charger (battery detached from pump)

Battery Charge Level Indicator
Icon displayed at full, mid, and low charge
Weight
5 oz (142 gm)
Dimensions
4.5 x 2.2 x 1.4 in (11.4 x 5.6 x 3.6 cm)
Case
Impact-resistant stainless steel with ABS/polycarbonate
Intrinsically Safe
UL and cUL Listed
RFI/EMI Shielding

RFI/EMI-shielded case
CE marked
Model 210-1002TX is ATEX approved (NiCad battery model only). Contact SKC.

Protect sample pump from weather when in use outdoors.

Pocket Pump FAQs

 

Ordering Information          

Pocket Pump - NiMH (Nickel Metal Hydride) Models
Description
Voltage
Cat. No.
Pocket Pump only, UL Listed, with NiMH battery (requires charger; see kits or accessories below)
ATEX-approved models available (NiCad battery models only); contact SKC
Pocket Pump, UL Listed, with NiMH battery and charger, with U.S. plug
115 V
Pocket Pump, UL Listed, with NiMH battery and charger, with U.S. plug
230 V
Single Pocket Pump Kit includes Pocket Pump with NiMH battery, single charger, and Type A tube holder, in a soft-side nylon carry case
115 V
230 V
Pocket Pump Starter Kit includes pump with battery, charger, Tygon tubing (3 feet, 1/4-inch ID), and collar clip with cable tie
115 V
230 V
Single Pocket Pump Kit with Hard-side Pelican Case includes pump with NiMH battery, single charger, Type A tube holder, and hard-side Pelican case
115 V
230 V
5-pack Pocket Pump Kit with Single Charger includes 5 Pocket Pumps with NiMH batteries, single chargers, and Type A tube holders, in a Pelican case
115 V
230 V
5-pack Pocket Pump Kit with Multi-charger* includes 5 Pocket Pumps with NiMH batteries and Type A tube holders and one 5-station charger, in a Pelican carry case
115 V
230 V
210-1001MH5D
Pocket Pump, ATEX Approved

Twin Port Pocket Pump with NiMH battery pack, for bag sampling applications, requires charger


Not UL listed for intrinsic safety

210-1002A Twin Twin Port Pocket Pump  
Pump Certificate
Cat. No.
Certificate of Compliance, optional, must be ordered when ordering pumps
Software
Cat. No.
DataTrac Software for Pocket Pump includes software on CD, DataTrac adapter, and DataTrac cable
Requires Windows 98 or higher and available serial port or appropriate adapter compatible with PC and system
Calibrators
Cat. No.
Defender Primary Standard Calibrator, 5 to 500 ml/min, includes lead-acid battery, charger, Optimizer software, and 39-inch (1-meter) serial cable
Software requires Windows XP (sp 2 or 3) or Windows Vista (32-bit version) and an RS-232 port or USB to RS-232 adapter
Defender Primary Standard Calibrator
Replacement Defender Lead-acid Battery Pack
Defender Universal Charger, 100-240 V, with U.S., Euro, and Australia plugs
Defender Universal Charger, 100-240 V, with U.S. plug
Chargers
Cat. No.
Multiple Charger, 5-station, 115 V, for UL Listed pumps, with U.S. plug
Multiple Charger, 5-station, 115 V
Multiple Charger, 5-station, 110-240 V, for UL Listed pumps, with U.S. plug
Multiple Charger, 5-station, 230 V
Single Charger, 115 V, for UL Listed pumps, CSA approved, with U.S. plug
Single Charger, 115 V
Single Charge, 230 V, for UL Listed pumps, with U.S. plug
Single Charge, 230 V
Replacement Battery Packs Cat. No.
Replacement NiMH Battery Pack, for UL Listed model
Replacement NiCAD Battery Pack, for UL Listed model
Pump Carry Cases Cat. No.
Kit Case: Single Deluxe, Pelican Kit Case: Single Deluxe (Pelican)
Kit Case: 5-Pack Deluxe, Pelican  
Kit Case: Single Nylon with Shoulder Strap Kit Case: Single Nylon with Shoulder Strap
Sampling Accessories
Cat. No.
Low Flow Constant Pressure Controller (CPC), for multiple-tube sampling
Low Flow Tube Holder with Plastic Cover
Cat. No.
A - for standard tubes 6-mm OD x 70-mm length
222-3-1
B - for tubes 7 or 8-mm OD x 110-mm length
222-3L-1
C - for tubes 10-mm OD x 150-mm length
222-3XL-1
D - for tubes10-mm OD x 220-mm length and shorter tubes
222-3XD-1
Replacement Parts and Tools Cat. No.
Replacement Valves for Pocket Pump, pk/2
Replacement Inlet Filter, pk/10
Inlet/Pressure Sensor Assembly
SKC Pneumatic Test Kit, for testing flow compensation in personal sample pumps, 1 to 5 L/min rotameter, 0 to 80 inches magnehelic pressure gauge
*
The Multi-charger is not CSA approved.
Pocket Pumps with NiCad battery packs are available from SKC Ltd. The pumps manufactured by SKC Ltd. will not be UL Listed, but will comply with the European regulations for intrinsic safety (ATEX).
Unlike other pumps, Pocket Pump contains circuitry that controls charging, therefore, the LED on PowerFlex will remain red during the entire charging process. The Pocket Pump LCD will display charge status.
Note:
Replacing batteries with non-approved battery packs voids the pump warranty and UL intrinsic safety approvals.

Pocket Pump Spec. Sheet (PDF)

Pocket Pump Operating Instructions (PDF)

Pocket Pump Quick Guide (PDF)

Battery Pack for Pocket Pump Operating Instructions (PDF)

Technical Note: SKC Sample Pump Battery Pack Characteristics and Maintenance (PDF)

MSDS for Nickel Cadmium Battery GPI International (PDF)

MSDS for Nickel Cadmium Battery SANYO Energy (PDF)

MSDS for Nickel-metal Hydride Battery (PDF)

UL Certificate of Intrinsic Safety (PDF)

EMC Test Certificate (PDF)

DataTrac for the Pocket Pump

Instrucciones de Funcionamento (PDF)

Téléchargement Guide de I'utilisateur (PDF)

Chinese Language Pocket Pump Operating Instructions (PDF)

Pocket Pump FAQs


SKC Air Sampling Pumps

Pump Accessories (Chargers, Calibrators, Flowmeters)


This page was last modified February 19, 2010
  About SKC Terms of Use Privacy Policy Contact Us Site Map Ordering Information
This site was last modified September 2, 2010
SKC Inc.'s Quality Policy is in Compliance with IS0 9001-2000
© Copyright 1995-2010 SKC Inc